lobifl.blogg.se - 5dtorgb gh4

#5dtorgb gh4 1080p
#5dtorgb gh4 full

The link below has 3 videos to compare - 4K H.264 straight from camera, the Firecoresoft ProResHQ 1080p exported out of FCPX as 1080p. The file size is enormous and from what I can see, no visual advantage for doing so.įirecoresoft will convert your 4K to ProRes also but you have the option of 1080p unlike 5DtoRGB. Earlier I mentioned that Firecoresoft 4K to ProResHQ 1080P converts were to be avoided but now I think they are OK - I was comparing it to 4K ProResHQ from 5DtoRGB - I had mistakenly assumed that the 5DtoRGB had transcoded the 4K to ProResHQ 1080p and that next to the Firecoresoft it looked inferior which it did but that is because using 5DtoRGB to transcode 4K into ProRes keeps it at 4K. I know quite specific questions, but perhaps someone has tried it or can try some of my regarding you post on May22nd - So here is what I found out about using 5DtoRGB and Firecoresoft Video Converter with GH4 4K clips. Is HDMI still live when connected with the Lumix Link app? In the GH4, can you adjust the settings during filming?Ĭan you see the preview of the picture on the app during the fliming? Now obvioulsy the questions for the GH4 owners: It comes back when you cancel the connettion between GH3 and Lumix link. So I connected a HDIM monitor to have the picture during the recording.īut, when Lumix link is activated, the HDMI picture disappears. Only a freezeframe of the first picture with a text that shows, how long it will record still. To end, you have to stop the recording at the camera.Īnd no adjustment of the settings during the filming.Īlso no live picture in the app during the recording. You have to enter a time how long you want to film in the app previous to the recoording. I can adjust all things via Lumix Link in photo mode.īut when you want to film with the GH3 via Lumix Link and Wifi, you can only start. I worked with the GH3 on a crane recently.

Note: To keep all of the 10Bit data, you can record in the following codec formats.I have a few questions to the Wifi function compared to the GH3. You can find a setup video for the GH5 and an Atomos recorder at the following link: (Setup begins at 1:23)

#5dtorgb gh4 full

An Intermittent connection between the camera and recorder when using a 4K60p output, is almost always caused by using a cable that can not handle the full signal bandwidth.

If the HDMI cable that is being used is not good enough, you will experience signal dropouts and breaks in your recording.

4Kp60 compatible HDMI Cables are available from Atomos at retail partners, under item numbers ATOM4K60C5, and ATOM4K60C6.

These cables are generally labeled "2.0a" (though not every 2.0a cable is made well enough to work properly). This is noted at the bottom of page 68 in the GH5 manual.Īnother important item needed is a high quality HDMI cable that is capable of handling the bandwidth of a 10Bit 4K60p signal. If either of these settings is not correct, the camera will not output the best quality 10Bit 4:2:2 4kUHD at 60p over HDMI. This setting can also be found under the "Motion Picture Menu."

"HDMI Rec Output" is set to 10Bit 4:2:2.

This setting can be found under the "Motion Picture Menu."

INTERNAL "Rec Quality" is set to 8Bit 4K 150M 60p.

To get the GH5 to output a 10bit 4:2:2 4KUHD60p signal, you must do the following:.

For the GH5 to have access to 60p video, the camera must be in NTSC (59.94 frequency) mode.If you are finding some difficulty in setting up the GH5 or GH5-S for HDMI output compatibility, please reveiw the following hints.